- Is there resistance in wire?
- What four things does the resistance of a wire depend on?
- How much is too much resistance in a wire?
- Which of the following will increase the resistance of a wire?
- What is the resistance of an open circuit?
- What causes high resistance?
- What is the resistance of a Nichrome wire?
- What does not change the resistance of a wire?
- Do all circuits need resistance?
- Does solid or stranded wire carry more current?
- What are 4 factors affecting resistance in a wire?
- What happens if a circuit has no resistance?
- What can be used instead of Nichrome wire?
- Can stranded wire be used in residential?
- What type of wire has the least resistance?
- What affects the resistance of a wire?
- What does not affect a material’s resistance?
- Does temperature affect resistance of a wire?
- Does copper have high resistance?
- Can you mix solid and stranded wire?
- Is it OK to use stranded wire in a breaker box?
Is there resistance in wire?
There is a resistance to the flow of an electric current through most conductors .
The resistance in a wire increases as: the length of the wire increases.
the thickness of the wire decreases..
What four things does the resistance of a wire depend on?
The resistance of a given piece of wire depends of three factors: the length of the wire, the cross-sectional area of the wire, and the resistivity of the material composing the wire. To understand how this works, think of water flowing through a hose.
How much is too much resistance in a wire?
resistance of wiring should ideally be zero. the DMM puts out so little current that even a wire with every strand but one broken should read close to zero. maybe one or two tenths of an ohm, tops. as stated, bending should not matter.
Which of the following will increase the resistance of a wire?
Increasing the resistivity of the material the wire is composed of will increase the resistance of the wire. Increasing the cross-sectional area of the wire will increase the resistance of the wire. Increasing the length of the wire will increase the resistance of the wire.
What is the resistance of an open circuit?
An open circuit implies that the two terminals are points are externally disconnected, which is equivalent to a resistance R=∞ . This means that zero current can flow between the two terminals, regardless of any voltage difference.
What causes high resistance?
Resistance measurements are normally taken to indicate the condition of a component or a circuit. The higher the resistance, the lower the current flow. If abnormally high, one possible cause (among many) could be damaged conductors due to burning or corrosion. … The lower the resistance, the higher the current flow.
What is the resistance of a Nichrome wire?
TypesMaterialResistivity (ohm-cmil/ft)Resistivity (10−6 ohm-cm)Nichrome675112.2Nichrome V650108.1Nickel41.696.93Platinum63.1610.511 more rows
What does not change the resistance of a wire?
Voltage value is not affect resistance (if we will not take into account any temperature changes).
Do all circuits need resistance?
Circuits HAVE resistance because the materials of which circuits are constructed HAVE resistance (usually.) SOME circuits NEED resistance in order to limit the current that flows in that circuit. The reason for limiting the current depends entirely upon the nature of the circuit.
Does solid or stranded wire carry more current?
Because of the given thickness of stranded wire, i.e., it’s thinner, there are more air gaps and a greater surface area in the individual strands of wire. Therefore, it carries less current than similar solid wires can.
What are 4 factors affecting resistance in a wire?
There are 4 different factors which affect resistance:The type of material of which the resistor is made.The length of the resistor.The thickness of the resistor.The temperature of the conductor.
What happens if a circuit has no resistance?
If there really were no resistance in the circuit, the electrons would go around the circuit, and arrive back at the beginning of the circuit with as much energy as the potential difference (the voltage). That final energy is usually what is dissipated as heat or other types of energy by the circuit.
What can be used instead of Nichrome wire?
Nichrome is good, steel or stainless steel should also work ok and may be preferred if you need less heat and more strength.
Can stranded wire be used in residential?
In a home the main advantage of stranded wire over solid wire is its ability to be bent easily in larger sizes. Normally #12 and smaller, the most common wiring in a house, is solid although it does not have to be as long as the terminations for it are designed for stranded wire.
What type of wire has the least resistance?
SilverSilver has the lowest resistivity. That means for a given length and diameter of wire it will also have the lowest resistance.
What affects the resistance of a wire?
The resistance of a wire is directly proportional to its length and inversely proportional to its cross-sectional area. Resistance also depends on the material of the conductor. See resistivity. … The resistance of a conductor, or circuit element, generally increases with increasing temperature.
What does not affect a material’s resistance?
The Resistance of the wire is also dependent on the temperature of the wire. Ohm’s law has no relationship with the resistance of the wire or the material. Thus, resistance of the material doesn’t depend upon the ohms law.
Does temperature affect resistance of a wire?
Heating a metal conductor makes it more difficult for electricity to flow through it. These collisions cause resistance and generate heat. … Heating the metal conductor causes atoms to vibrate more, which in turn makes it more difficult for the electrons to flow, increasing resistance.
Does copper have high resistance?
Copper has a lower resistivity and is a better conductor of electricity than iron. … Copper is a better conductor than iron, which means current can flow easier (with less resistance) through copper. This is an inherent property of a material.
Can you mix solid and stranded wire?
Note: If you hold the ends of solid and stranded wire even with each other while you screw on the wire nut connector, the stranded wire will often wrap loosely around the solid wires, resulting in a loose connection. This is especially likely when you’re joining multiple solid wires to one stranded wire.
Is it OK to use stranded wire in a breaker box?
In general, breakers don’t care what sort of wire is attached. However, it’s generally good practice, to use a bootlace ferule crimped onto finely stranded wire to stop strands spreading. It’s essentially where there’s any form of screw connection.